GOC1728906-CT-BAG - Contractor - Urgent Replacement of Holding Tank

Statement of Work/Overview:
FOR THE PURPOSES OF THIS PROJECT, 'PROVIDE' SHALL MEAN TO SUPPLY AND INSTALL.
1.         DEMOLISH EXISTING WATER CLOSET WC-1 IN WASHROOM. REMOVE DRAIN FLANGE, CAP AND SEAL EXISTING DRAIN PIPING SYSTEM. ENSURE FLAT AND LEVEL FLOOR SURFACE FOR NEW TOILET.
2.         PROVIDE ALL APPURTENANT PIPING, WIRING, FIXTURES AND WORKS AS INDICATED.
3.         PROVIDE NEW WASHROOM MACERATING UNIT MU-1.
4.         PROVIDE NEW WATER CLOSET WC-2.
5.         CONNECT LV-1 AND WC-2 TO MU-1.
6.         PROVIDE ONE 15A 120V BRANCH CIRCUIT FOR MU-1.
7.         CONNECT MU-1 DISCHARGE AND VENT PIPING DIRECTLY, VERTICALLY, THROUGH ATTIC.
8.         PROVIDE NEW MACERATING UNIT MU-2 TO SERVE KITCHEN SINK KS-1.
9.         DISCONNECT KITCHEN SINK FROM EXISTING DRAIN SYSTEM. CAP AND SEAL DRAIN PIPING SYSTEM.
10.       CONNECT KS-1 TO MU-2.
11.       PROVIDE ONE 15A 120V BRANCH CIRCUIT FOR MU-2.
12.       CONNECT MU-2 DISCHARGE AND VENT PIPING DIRECTLY, VERTICALLY, THROUGH ATTIC.
13.       PROVIDE FIRE STOPPING AS REQUIRED.
14.       PROVIDE BACKFLOW PREVENTER TO MU-1 AND MU-2 AS REQUIRED.
15.       PROVIDE NEW HOLDING TANK PU-1.
16.       PROVIDE HEAT TRACING AND INSULATION TO PU-1 PER SPECIFICATIONS.
17.       PROVIDE NEW HEAT TRACING CONTROL PANEL CP-1, WALL MOUNTED.
18.       PROVIDE ONE 30A 240 V BRANCH CIRCUIT FOR CP-1.
19.       CONNECT (HARDWIRED) CP-1 TO EXISTING ELECTRICAL DISTRIBUTION PANEL C.
20.       CONNECT DISCHARGE PIPING OF MU-1 AND MU-2 TO PU-1.
21.       PROVIDE PIPEWORK INSULATION PER SPECIFICATIONS.
22.       PROVIDE IDENTIFICATION FOR NEW ALL EQUIPMENT, DISTRIBUTION PIPEWORK AND VALVES PER SPECIFICATIONS.
23.       MAKE GOOD AND OTHERWISE REPAIR AND REINSTATE ALL SURFACES AND FINISHES AFFECT BY WORK OF THIS PROJECT.
24.       CLEAN AREA OF ANY DIRT AND DEBRIS CREATED DURING THE WORK OF THIS PROJECT.
25.       PERFORM MINIMUM 8 HOURS OF SITE INSTRUCTION TO BGIS STAFF ON OPERATION AND MAINTENANCE OF NEW AND ALTERED SYSTEMS.
26.       PROVIDE ALL LABOUR AND MATERIALS REQUIRED TO ASSIST COMMISSIONING OF ALL THE ALTERED AND NEW EQUIPMENT. 
27.       COMPLETE CMMS DOCUMENT FOR ALL NEW EQUIPMENT INSTALLED AT THIS FACILITY.
AFTER CONSTRUCTION COMPLETION, ISSUE MARKED UP DRAWINGS INDICATING ANY AND ALL DEVIATIONS FROM THE DRAWINGS AND PROVIDE TWO COPIES TO BGIS PROJECT MANAGER AND CONSULTANT FOR REVIEW, AS PART OF CLOSE OUT DOCUMENTS (GC TO ISSUE ELECTRONIC COPY OF O&M BINDER PRIOR TO SUBSTANTIAL FOR REVIEW). ONLY PRINT TWO HARD COPIES OF BINDERS AFTER ELECTRONIC COPY HAS BEEN APPROVED BY CONSULTANT & COMMISSIONING MANAGER.
The Awarded Contractor must ensure compliance with required latest applicable Code, standard, safety acts, best practices, security and tender documents. Make good / Reinstate all areas affected by work. Project is planned for completion latest by MARCH 18, 2018. GC to provide safety hoarding to separate construction area from public area. Ensure inclusion of all cost associated with winter work (i.e. snow removal at affected work areas where required, heated enclosures etc.). Contractor to test (megger) the cable before covering and Consultant to review the results. If the results are not good, GC will stop the concrete pouring until the cables are checked, retested and confirmed acceptable by Consultant. Contractor to document and conduct Flood testing on cables and GFI system before the pour. Provide weekly progress site photos (with work description) and performance verification forms signed by Consultant and manufacturer. Issue electronic copy of close out documents via email for stakeholders’ approval prior to Substantial Inspection.